support > Wheelchair Mounting > Adapter Plate 2

Picture examples your Frame Type

Pride Quantum/Jazzy Tiedown

 unmounted Motion Concepts Matrx PB.  
unmounted Motion Concepts Matrx PB.  
Or, you can check out a step-by-step example here

Permobil UniTrack

 unmounted Invacare Pronto M41.  
unmounted Invacare Pronto M41.  
Or, you can check out a step-by-step example here

Permobil Corpus

 unmounted Invacare Solara Jr  
unmounted Invacare Solara Jr  

 

Attachment Diagrams for Pride: Quantum or Jazzy Wheelchairs

Wheelchair Adapter Plate 2(WC-AP2)
Wheelchair Adapter Plate 2(WC-AP2)
Quantum Rail with Tie Down Illustrations
Quantum Wheelchair Frame with Tie-Down

Attaching an Adapter Plate 2 to a Quantum Wheelchair Frame with Tie-Down

AP to Holes Illustration
AP to Holes Illustration

Tools needed:
  • 1/2" Socket, Box, Open or an Adjustable-End Wrench
  • One "Quantum" Bolt (provided in the WC-AP2 packet)

Attachment Instructions

Notes for installation: If possible, we recommend that the wheelchair user not be seated during installation.
Try to have the wheelchair tilted as level as possible.
Removing the Quantum Tie-Down
  1. Remove the bolt that is towards the rear of the wheelchair first.
  2. Remove the other bolt attached to the tie-down.
    Please note if the wheelchair is occupied during installation, be careful to maintain the alignment of the seat rail and the cross-frame (under the seat pan). This is done by re-threading the same bolt thru the back, into the seat rail.
  3. Typically, the shorter bolt attaches to a slide-track nut. This nut may slide out of reach if the wheelchair is tilted. Try and keep this nut in its original location (aligned with the tie-down). Do not lose this slide-track nut.
Attaching/Sandwiching the Wheelchair Adapter Plate 2 with the Quantum Tie-Down
  1. Align the WC-AP2 with the Quantum Tie-Down, then screw bolts back into the wheelchair frame. Start with the longer of the two bolts first.
    Using the "Quantum" Bolt provided with the WC-AP2, Screw the second bolt into the slide-track nut.
  2. Make sure that both fasteners are engaged in the respective threads, and then torque both fasteners down.

>>See the Step-By-Step Instructions

Picture Examples of mounted Quantum Wheelchairs with Tie-Downs

Mounted Quantum Wheelchair Picture - Side Mounted Quantum Wheelchair Picture - Isometric Mounted Quantum Wheelchair Picture - Front
Components used in this example: Wheelchair Adapter Plate 2 (WC-AP2), a Wheelchair L-Angle Extension Plate (WC-LAE), and a Solid Wheelchair Bracket WB2(solid)

Back to top

Attachment Diagrams for the Permobil Uni-Trac Wheelchairs

Wheelchair Adapter Plate 2(WC-AP2)
Wheelchair Adapter Plate 2(WC-AP2)
UniTrack Rail Illustrations
Permobil UniTrack Wheelchair

Attaching an Adapter Plate 2 to a Permobil Uni-trac Frame Wheelchair

AP to Holes Illustration
Tools needed:
  • 5mm Hex Key (reccommended), or 3/16" Hex Key (provided with every Mount'n Mover)
  • Four "Uni-Trac" 6mm Bolts (provided in the WC-AP2 packet)
  • Four "Uni-Trac" 6mm Nuts (provided in the WC-AP2 packet)

Attachment Instructions

  1. Remove the plastic end cover that is on the uni-trac rail.
  2. Insert the four bolts into the WC-AP2 holes (shown in the diagram). Partially thread the four Nuts onto the ends of the bolts after you do.
  3. Align the nuts so that the WP-AP2 assembly can enter and slide within the Uni-Trac.
    Position the WC-AP2 for best function, and torque all the fasteners down.
    Don't forget to replace the cap.

 

>>See the Step-By-Step Instructions

Picture Example of a mounted Permobil Uni-Trac Wheelchair

Mounted Permobil Uni-Trac Wheelchair Picture - 1 Mounted Permobil Uni-Trac Wheelchair Picture - 2 Components used in this example: Wheelchair Adapter Plate 2 (WC-AP2)

Back to top

Attachment Diagrams for the Permobil Corpus Frame Wheelchairs

Wheelchair Adapter Plate 2(WC-AP2)
Wheelchair Adapter Plate 2(WC-AP2)
corpus Rail Illustrations
Permobil corpus Wheelchair

Attaching an Adapter Plate 2 to a Permobil Corpus Frame Wheelchair

AP to Holes Illustration
Permobil Corpus Frame with Thigh Support Bracket
Tools needed:
  • 5mm Hex Key (reccommended), or 3/16" Hex Key (provided with every Mount'n Mover)
  • Three M6x50mm Bolts (use the same ones that attach the thigh support) or,
  • Two M6x45mm Bolts (provided in the WC-AP2 packet) or,

Attachment Instructions

    With thigh support:
  1. remove the three bolts attached to the thigh support bracket, and remove the unit.
  2. Sandwich the WC-AP2 with the thigh support bracket, and use the washers on the hole not occupied by the WC-AP2
  3. Screw down all three bolts, and check that the mounting is properly fastened.
    Without thigh support:
  1. Attach the WC-AP2 using the two bolts provided in the packet.
  2. Screw down both bolts, and check that the mounting is properly fastened.

 

Picture Example of a mounted Permobil Corpus Frame Wheelchair

Shown in two options for bolting the WC-AP2
Mounted Permobil Corpus Frame, shown without thigh supports   Mounted Permobil Corpus Frame, shown without thigh supports
Components used in this example: Wheelchair Adapter Plate 2 (WC-AP2)

Back to top

Have more questions?

Don't see your chair type?

These are only a few examples of how some people have successfully mounted to their wheelchairs.
We understand that every case is different, so If you have any questions about mounting or the Mount'n Mover in general,
email us, or call us at 1(888)724.7002 / 1(612).724.7002.

Go back to the mounting section
Back to top

On this page:

Other Frame Types

Not the right frame-type? try these:

Related Support Pages

How can we help you?

Warranty info

  • One year warranty
    BlueSky Designs offers a one year warranty on the Mount’n Mover
  • 30 Day Return Policy
    30 day money back guarantee for unused items
    • Click here for more information