support > Floor Stand
Great for evaluations and access from a bed or the floor!
The new Mount'n Mover Floor Stand positions devices anywhere from 6 inches all the way to 6 feet off the floor.
Simply remove your Mount'n Mover from your wheelchair or table mount and insert it into the Floor Stand!
Once the Floor Stand is set, it takes seconds to attach to your Mount'n Mover to it with no tools required.
Check out the floorstand upgrade options
You can also download and print the manual here: Floor Stand Instructions
Angle Adjustment
To ensure level device positioning or to achieve angled device viewing positions, you can adjust the post angle of the Mount'n Mover Floor Stand 10° in either direction.
To adjust the angle
- Find the adjustment bolt on the silver plate-the one which is in a curved slot.
- Using a 3/16" Hex Key, loosen that bolt.
(you may have to also loosen the accompanying bolt slightly) - With the device attached to the Mount' Mover, extend the device to the desired position.
While supporting the Mount' Mover, adjust the Floor Stand post angle to best suit your needs. - Once it is in the desired position, tighten both adjustment bolts.
Height Adjustability and Range
There are two telescoping post elements in the Floor Stand:
- Floor Stand Post
(telescopes within the Upright Rail) - Mount'n Mover post
(telescopes from the Floor Stand Post)
The Floor Stand post clamp allows you to insert the post attached to your Mount' Mover-the same one used for a wheelchair mount.
This makes it easy to move your Mount'n Mover from the wheelchair or table clamp to the Floor Stand without any additional adjustments.
The additional height adjustment makes it easy to accommodate a variety of needs, from access in a bed, recliner, wheelchair, the floor, or a standing position.
High Positions (24" - 72")
The Mount' Mover will usually be attached to the top of the post for higher positioning.
For use in higher positions, the post is inserted into the Floor Stand clamp from above.
Height adjustments are made at either the Upright Rail or the Floor Stand clamps.
Low Positions (6" - 24")
To set the Floor Stand for lower positions, the post is set so it comes above the Mount'n Mover arms, up through the Link (see photo).
In this case, the post is inserted into the Floor Stand clamp from below, enabling positioning of the Mount'n Mover from the floor level to the Floor Stand clamp.
TIP:
It is easiest to adjust the height when the device (majority of the weight) is as close as possible to the Upright Rail.Relocating: from wheelchair to Floor Stand
Relocating your Mount'n Mover from wheelchair to Floor Stand
You can easily move your mount and device from your wheelchair
(or table clamp) to the Floor Stand, no tools required.
No need to get two separate mounting systems!
Cautions
Because the Mount'n Mover is so flexible, there are areas it can reach that may make the Floor Stand system unstable, particularly when a heavy device set at a very high position is extended outside the wheel and caster base.
Stay within the wheel and caster "footprint".
You should be safe if you avoid using the device in the area in red. In this area, there is an increased risk for tipping.
Maximum Height
Please also keep in mind that there is a "height limit" built into the floor stand post.
If it does not extend any further, it has likely reached its maximum height.
Basic Model (FS)
The basic floorstand model has all the features covered in "Getting to know your floorstand"
Features include :
- Compatible with any Mount'n Mover with post
- Two rear "Total-Lock" casters
- Locks the caster swivel and wheel rotation - Vertical Telescoping Post
- Height adjustment of up to 20" (plus the length of the Mount'n Mover Post) - Angle adjustment
- Up to ± 10°
Floorstand with Extension (FS-E)
Allows you to extend your Mount'n Mover up to 16" from the floorstand upright-rail.
This works perfectly for folks who need that extra distance for bed access.
Features include :
- Compatible with any Mount'n Mover with post
- Two rear "Total-Lock" casters
- Locks the caster swivel and wheel rotation - Vertical Telescoping Post
- Height adjustment of up to 20" (plus the length of the Mount'n Mover Post) - Angle adjustment
- Up to ± 10° - Adjustible offset extension
-Extends your mount bracket up to 16"
Floorstand with Four Total-Lock Swivel Casters (FS-4C)
Four "Total-Lock" casters allow you to maneuver the floorstand a lot easier!
"Total-Lock" casters brake the wheel and lock the swivel with one action.
The four-caster floorstand is perfect for folks who use eye-gaze devices, or for those who reposition their floorstands a lot.
For direct-select devices, we recommend locking all four casters for best stability.
Features include :
- Compatible with any Mount'n Mover with post
- Four "Total-Lock" casters - Easy to maneuver in any direction
- Vertical Telescoping Post - Height adjustment of up to 20" (plus the length of the Mount'n Mover Post)
- Angle adjustment - Up to ± 10°
Floorstand with Four Casters and Extension (FS-4C-E)
Ease of maneuverability with extended reach!
For folks who need access to their devices past the reach of their Mount'n Mover, and prefer the enhanced maneuverability of four swivel casters.
Features include :
- Compatible with any Mount'n Mover with post
- Four "Total-Lock" casters - Easy to maneuver in any direction
- Vertical Telescoping Post - Height adjustment of up to 20" (plus the length of the Mount'n Mover Post)
- Angle adjustment - Up to ± 10°
- Adjustible offset extension -Extends your mount bracket up to 16"
Other Mounting
Other Support Pages
Warranty info
- One year warranty
BlueSky Designs offers a one year warranty on the Mount’n Mover - 30 Day Return Policy
30 day money back guarantee for unused items
Click here for more information